Skip to main content
GullySystem
Manufacturing

Bill of Materials for Control panel manufacturers

Define the materials and quantities needed for a manufactured item.

Manufacturing

Does this function belong in your operation?

Use when output quantities depend on a repeatable material or component list.

A product or production recipe is created or revised.

A panel’s list holds breakers, busbars, contactors, relays, cable glands and ferrules by position in the cabinet. Approved alternative makes are listed too. The shop floor reads quantities per section.

Bring the records the workflow depends on.

  • Finished-item codes
  • Component quantities and units
  • Revision and waste rules

Outputs to check

  • Approved material and subassembly list
  • Versioned material cost basis
  • Quantity-exploded requirement sheet

Follow the bill of materials workflow.

Use this sequence to compare your current process with the proposed module. Agree the owner, permission and exception at each step.

  1. 1. Define the output

    Identify the finished item, production quantity and unit.

  2. 2. List components

    Record materials, subassemblies and quantity conversions.

  3. 3. Review allowances

    Approve waste factors and permitted substitutes.

  4. 4. Release a version

    Retain the approved definition and its effective use.

  5. 5. Calculate requirements

    Expand the selected version for a planned quantity and pass shortages to planning or purchasing.

Who uses the module, and who approves?

Keep responsibilities distinct even when one person holds more than one role.

Estimator

Defines the material quantities and approved version used to cost a finished item or quotation.

Production in-charge

Sees what a job needs before it is released to the floor.

Storekeeper

Issues against the list. Anything beyond it is asked for in writing.

Decide how exceptions are handled.

These business rules belong in configuration and testing. A normal transaction alone does not demonstrate that the workflow is ready.

Component unavailable

Use only an approved substitute and retain its effect on cost and specification.

Design revised after release

Keep existing jobs on their approved version unless a controlled change is authorised.

Unit conversion inconsistent

Resolve the conversion before calculating requirements or issuing material.

Can this work independently?

A bill of materials can be maintained independently for costing and planning. Stock, purchasing and work orders use its approved version when connected. It does not reserve materials or schedule machines by itself, and a rate-based material total excludes labour or overhead unless separately defined.

Systems and records it connects with

  • Production planning: Demand, planned quantities and resource or material constraints.
  • Work orders: Released production jobs, material issues and output records.
  • Purchase orders: Authorised supplier commitments and open line balances.
  • Stock: Item-location quantities and authorised stock movements.

Configure, test and introduce the workflow.

  • You show a few finished items and describe how they are made. You get a written note on how the parent items and sub-assemblies will be laid out. Begin with a few products.
  • You supply item names, units and wastage habits from your sheets. A trial import comes back for you to correct before anything is relied on. Corrections come cheaply here. Recent purchase rates are connected to the lines. A costed list for a few products is laid beside your own working for comparison.
  • The estimator and the storekeeper explode a batch on the trial. You hear what is missing, and the layout is changed. Gaps surface early. New quotations start from the list. The team is shown how to save a version and how to mark alternates.

Check the result before rollout.

Apply these checks to a sample from the agreed workflow, then repeat with an exception. Keep the expected result beside the test record.

  • Component units are consistent.
  • Production uses the approved version.
  • Revisions preserve the earlier material definition.
Control panel manufacturers

How the business operates.

An order arrives as a single-line diagram, a load list and a consultant’s specification. You size the enclosure and copper busbar, price moulded case breakers, contactors, soft starters and relays, and send a general arrangement drawing for approval. Revision C is not revision B. Parts are bought against whichever one the customer signed, and a large air circuit breaker or drive can set the delivery date.

Enquiry pricing from load lists

Price a board from the load list and single-line diagram using your rates for enclosures, copper busbar and breakers.

Drawing revision control

Hold each general arrangement and schematic revision with the consultant’s approval status and comments.

See the full industry workflow, reports and implementation plan →

The records that hold the operation together.

  • Load list enquiries. Enter motors, feeders and control functions from the customer’s load list, then pick the panel type, whether an MCC bay with withdrawable starters or a changeover panel with an ATS controller. Enquiries start here.
  • Panel pricing. Price enclosure, tinned copper bar, components and labour from rate tables, and keep every revision of the offer that went out. Compare any two side by side.
  • Drawing revisions. Hold general arrangement and schematic revisions with their comment rounds, and mark the single one approved for release to the bay. Every other print is locked out of circulation.
  • Panel component lists. List the MCCBs, contactors, relays and terminal blocks for each cabinet, with any substituted make shown beside the specified one. Totals follow without a second spreadsheet.

Operational bottlenecks to check

Drawing revisions drift from the shop floor

Schematics are revised after the consultant’s comments, yet the wiring team may still hold the earlier print on the bench, because nobody collected it when the new sheet was issued. The board is wired to the wrong revision. It surfaces at the megger test and goes back to the bay.

Component lists are rebuilt for every panel

Breakers, contactors, thermal overload relays, DIN rail terminals, ferrules and drives are listed in a spreadsheet per job, and each copy drifts. Substitutions made at the counter are not written back. The as-built list then differs from the drawing that was approved.

How work flows across this business

This module sits within a wider operating process. Use the sequence to identify the other teams and records affected by a change.

  1. 1. Enquiry and load list

    A customer sends a single-line diagram and load list, and each DOL starter, star-delta set, feeder and control function is entered before the panel type is chosen. Nothing is retyped later.

  2. 2. Quotation

    The panel is priced from enclosure, busbar, component and labour rates, and because customers keep changing motor ratings, every revision of the offer is kept with the figures that were sent. Old offers stay readable.

  3. 3. Drawings and approval

    General arrangement and schematic revisions go out for comment, remarks are logged by round, and only the approved revision is released to the wiring bay. Older prints are withdrawn at once.

  4. 4. Procurement and kitting

    The component list becomes supplier orders for MCCBs, thermal overload relays and DIN rail terminal blocks, and parts that arrive are checked against the list and kitted to the cabinet. Shortages show early.

  5. 5. Build, wiring and test

    The bay cuts the enclosure, mounts the back plate, then wires and ferrules the cabinet, and the test engineer records megger and functional readings against the approved drawing. A witnessed test carries the witness’s name.

  6. 6. Dispatch and service

    As-built drawings, the test sheet and nameplate details travel with the delivery note, and later site calls are logged against the cabinet serial. The record stays open for the life of the panel.

Industry reports to connect with

  • Panels by build stage and customer
  • Schematic revisions awaiting approval by age
  • Late VFDs and breakers by the panel they hold
  • Megger and functional failures by type and cabinet

Questions before implementation.

When should control panel manufacturers consider bill of materials?

Use when output quantities depend on a repeatable material or component list. A product or production recipe is created or revised.

What should we bring to the requirements discussion?

Bring anonymised examples of Finished-item codes; Component quantities and units; Revision and waste rules. Show who creates, checks and changes each record. Use only records from an activity that meets the suitability conditions above.

Does this replace our existing business software?

The starting point is your current system and the gap you need to close. Define the materials and quantities needed for a manufactured item. Configuration, a connected module or a custom build are evaluated against that gap before a replacement is proposed.

What is outside this module?

Use only for operations that make, assemble or formulate physical goods; ordinary service delivery needs a different workflow.

How are scope, price and rollout decided?

The proposal follows a review of your records, user roles, branches and existing software. Data migration, connections, training and support are scoped separately where needed. Component units are consistent. Use this check when reviewing the first working version.

Talk to us

Discuss bill of materials for your business.

Tell us which workflow needs attention and which systems your team uses. The next step is a requirements discussion and a written scope.

What happens after you share your requirements

  1. We review your brief and the systems you already use.
  2. We clarify the workflow, missing information and the work to consider first.
  3. The proposed scope sets out the deliverables, responsibilities and dependencies.
  4. Review the scope and commercial terms before deciding whether to proceed.

Start with your requirements

Describe your current process, the people involved and the change you need. Start with the details you know; we can clarify the rest together.

Share your requirements