Skip to main content
GullySystem
Manufacturing

Job Work Management for Precision component manufacturers

Track material sent to an outside processor and returned after work.

Manufacturing

Does this function belong in your operation?

Use when your materials leave for processing and must be reconciled on return.

A production stage is subcontracted with material supplied by your business.

Small component lots sent for plating, hardening or deburring need a count that follows the dispatch note and the originating router. Configure mixed collections as separately identified lines so a processor's combined return does not blur one buyer's bushes with another buyer's pins. Returned components remain subject to the shop's acceptance checks before they rejoin the next operation. Preserve the relationship between the outside operation and the stage that follows it. A component returned from hardening may still need grinding or inspection before packing. The production controller should see that remaining route, rather than interpret a reconciled subcontract return as completion of the customer's entire manufacturing lot.

Bring the records the workflow depends on.

  • Component and router identifiers by dispatch line
  • Count and supporting weight at handover
  • Specified outside operation and required evidence
  • Processor return commitment and approved charges

Outputs to check

  • Outstanding component lots at outside processors
  • Line-by-line return and rejection reconciliation
  • Accepted-processing charge support

Follow the job work management workflow.

Use this sequence to compare your current process with the proposed module. Agree the owner, permission and exception at each step.

  1. 1. Define outside processing

    Record the vendor, process and expected return terms.

  2. 2. Dispatch material

    Identify quantities, lots and the linked delivery document.

  3. 3. Track work outside

    Keep material balances and promised returns by processor.

  4. 4. Receive and inspect

    Record accepted output, waste and unresolved differences.

  5. 5. Reconcile charges

    Match processing bills and close only the settled material balance.

Who uses the module, and who approves?

Keep responsibilities distinct even when one person holds more than one role.

Outside-process buyer

Confirms the operation and return terms and follows each unreturned line.

Goods-in inspector

Separates returned lots and records shortages, damage or unacceptable finish against the correct dispatch.

Production controller

Updates the next operation only from quantities actually accepted back into the shop.

Decide how exceptions are handled.

These business rules belong in configuration and testing. A normal transaction alone does not demonstrate that the workflow is ready.

Processor combines several lots

Require clear component identification and reconcile each original dispatch line.

Pieces are returned bent or damaged

Keep the affected quantity separate and record the responsible quality disposition.

Rework is sent back out

Link the second movement to the original lot so it does not inflate production quantities.

Can this work independently?

This can track outside processing with entered dispatch and receipt records. Stock and accounting connections reconcile material ownership and processing charges; quality control decides acceptance. A vendor's completion message is not a physical return or proof that the returned output meets specification.

Systems and records it connects with

  • Work orders: Released production jobs, material issues and output records.
  • Stock: Item-location quantities and authorised stock movements.
  • Vendor bills: Supplier invoice lines and authorised posting status.
  • Purchase returns: Approved supplier-return quantities and adjustment references.

Configure, test and introduce the workflow.

  • We list the outside processes you use and the vendors for each. You describe how notes and returns are handled today. A flow diagram comes back for your approval.
  • Rates, process names and wastage allowances are entered. You confirm them with the production team. Material currently lying outside is loaded from your registers. The store team checks balances with the vendors. Mistakes surface early.
  • New outward notes are made on the screen while the old book continues. Returns are booked and compared. The team is trained. The paper book is retired. The oldest balances are reviewed at the next meeting.

Check the result before rollout.

Apply these checks to a sample from the agreed workflow, then repeat with an exception. Keep the expected result beside the test record.

  • A combined vendor delivery can be traced back to individual component dispatches.
  • Rejected returns remain separate from components available for the next operation.
  • The payable processing quantity reconciles with the agreed commercial basis and accepted evidence.
Precision component manufacturers

How the business operates.

You turn, mill and grind shafts, bushes, spindles and dowel pins to a drawing, and a micrometer, bore gauge or CMM decides whether each one passes. Runs are short. The same bush returns under a new revision letter.

Enquiries, drawings and revisions

Log each enquiry with its drawing and keep every revision letter against the part number. The order, the work order and the router all name the agreed revision, and a stale one is flagged before release.

Routers, work orders and job cards

Set the turning, milling and grinding sequence for each part, release a work order per lot, and record quantity passed, rejected and held at each stage. Operator and shift travel with every card.

See the full industry workflow, reports and implementation plan →

The records that hold the operation together.

  • Enquiries and production quotations. Log buyer enquiries with the drawing or sample attached, then cost bar weight, machine minutes and outside plating before a price goes back to the purchasing desk. Every costing revision is kept.
  • Sales orders and delivery commitments. Hold confirmed orders with part number, drawing revision, quantity, rate, schedule and the delivery week promised to the buyer, so a balance after each part delivery is always visible. Late orders stand out.
  • Multi-level bill of materials and routing. Keep each part’s material list and stage sequence. Drawing revisions, scrap allowance, the CNC lathe or press brake each stage runs on and the fixture it needs sit beside it. A sub-assembly carries its own list.
  • Work orders and batch planning. Release a work order for a batch, set its target date, and see the load already queued on each machine and stage. Planners move dates by hand. Overloaded stages stand out.

Operational bottlenecks to check

An old revision gets machined

A buyer revises a drawing by email, yet the router at the lathe still says revision B. A lot of 800 shafts is bored to the superseded diameter and scrapped, because the email sat in one inbox.

Inspection readings stay on paper

Bore, runout and Ra readings are written on sheets kept in a drawer beside the surface plate. A buyer’s query a month later means digging through that drawer by hand.

How work flows across this business

This module sits within a wider operating process. Use the sequence to identify the other teams and records affected by a change.

  1. 1. Enquiry and costing

    A buyer sends a drawing. The unit works out bar weight, machine minutes and plating charges, and a quotation goes back against that enquiry with the drawing revision noted.

  2. 2. Sales order

    The buyer confirms by purchase order, mail or WhatsApp. Quantity, rate, part number, drawing revision and the promised delivery week go on the order, so planning starts from facts and nothing is retyped.

  3. 3. Work order and material planning

    A work order opens for a batch. The bill of materials lists the bar, sheet or granule that the store must issue by grade and size, with scrap allowance added for the cut length. Shortages go to purchase as a requirement.

  4. 4. Production stages

    The batch moves on its job cards through sawing, turning, welding, assembly or filling, and each stage records quantity passed, rejected and sent for rework. The operator, machine and shift are named on every card, so piece counts reconcile when the batch closes and nobody argues about a shortfall.

  5. 5. Quality and packing

    Final inspection records go/no-go gauge results. Accepted pieces are packed in cartons, labelled and taken into finished goods, while any held lot waits for a decision from the quality head and the planner.

  6. 6. Dispatch, billing and follow-up

    The delivery note and the tax invoice both come from the work order, and payment follow-up is tracked after dispatch along with the next order from the same buyer.

Industry reports to connect with

  • Work orders still open, grouped by stage and promised week
  • Production by stage, machine and operator each shift
  • Material consumed against the bill of materials
  • Rejection and scrap by stage and reason

Questions before implementation.

When should precision component manufacturers consider job work management?

Use when your materials leave for processing and must be reconciled on return. A production stage is subcontracted with material supplied by your business.

What should we bring to the requirements discussion?

Bring anonymised examples of Component and router identifiers by dispatch line; Count and supporting weight at handover; Specified outside operation and required evidence; Processor return commitment and approved charges. Show who creates, checks and changes each record. Use only records from an activity that meets the suitability conditions above.

Does this replace our existing business software?

The starting point is your current system and the gap you need to close. Track material sent to an outside processor and returned after work. Configuration, a connected module or a custom build are evaluated against that gap before a replacement is proposed.

What is outside this module?

This concerns outsourced physical processing, not general professional-services subcontracting.

How are scope, price and rollout decided?

The proposal follows a review of your records, user roles, branches and existing software. Data migration, connections, training and support are scoped separately where needed. A combined vendor delivery can be traced back to individual component dispatches. Use this check when reviewing the first working version.

Talk to us

Discuss job work management for your business.

Tell us which workflow needs attention and which systems your team uses. The next step is a requirements discussion and a written scope.

What happens after you share your requirements

  1. We review your brief and the systems you already use.
  2. We clarify the workflow, missing information and the work to consider first.
  3. The proposed scope sets out the deliverables, responsibilities and dependencies.
  4. Review the scope and commercial terms before deciding whether to proceed.

Start with your requirements

Describe your current process, the people involved and the change you need. Start with the details you know; we can clarify the rest together.

Share your requirements