Skip to main content
GullySystem
Manufacturing

Business solutions for Rubber moulding companies

Explore software for work such as “Every drawing answered with a question about the parting line or the tolerance”. Review each business function below, including when it fits and what to check before implementation.

Rubber moulding companies

How the business operates.

A rubber moulding shop makes bushes, grommets, bellows, mounts and bonded rubber-to-metal parts. Raw rubber and fillers are mixed into compound on a mill or an internal mixer. Strips or preforms are cut to weight, loaded into a heated mould and cured under pressure. What decides quality is the mix that went in, the cavity that shaped it and how long it sat under heat and pressure.

Compound batches and test results

Record each mix with its recipe, rheometer curve, hardness and specific gravity, and mark the batch as released or held.

Mould and cavity register

Hold each mould with its cavity count, press fit, shot history, repairs and the date it was last cleaned.

Press cure settings

Keep cure time, temperature and pressure per mould and compound, and show them on the operator’s screen at the press.

Preform and shot records

Log preform weight, shots and good parts per cavity for each run, with scrap sorted by cause.

Trimming and post-cure

Follow parts through deflashing and post-cure ovens with loads, times and the inspector’s release.

First-off and part approvals

File each approved sample with its measurements and the buyer’s sign-off, so later runs are checked against it.

Bags, labels and delivery

Parts are counted into bags marked with part number, batch and date, and the buyer’s certificate goes out with the delivery.

Mould repair and refurbishment log

Records every mould sent for cavity polishing, vent cleaning or dowel repair, with the date out and the tool room holding it. Planners read it before booking a press. A mould in repair cannot be scheduled by mistake.

Customer drawing revision register

Holds each drawing issue received from a buyer, with hardness, tolerance and compound changes marked against the previous issue. Quoting and the press shop see the same live revision. Old drawings stay filed as superseded.

Rejected part and rework notes

Captures parts pulled for flash, short fill, porosity or bond failure, with the count, the cause and the decision to trim, rework or scrap. Quality staff sign each note. Scrap value is added up by mould.

The records that hold the operation together.

  • Enquiries and drawing quotations. Log each buyer drawing and price it from compound cost, preform weight, cure time and cavity count. Every revision of the quote is kept.
  • Compound recipes and batches. Hold recipes with polymer, carbon black, filler and curative shares. Record each mix with its rheometer curve, scorch time, hardness and release status.
  • Mould and cavity register. Track every mould with cavity count, press fit, shot count since cleaning and repair history. Plating, venting and dowel pin work is logged too.
  • Press cure settings. Store time, temperature and pressure for each mould and compound pair, then show them at the press, so the tag on the wall is no longer the record.
  • Preform cutting and weights. Record preform weight limits per part. The cutter operator logs checks at the bench scale, and a drifting weight is flagged before short fills reach the cavities.
  • Press scheduling and run sheets. Plan orders by press, mould change and compound availability. Log shots, good parts and rejects per cavity on the run sheet.
  • Rubber-to-metal bonding records. Record insert type, bonding agent lot and bond test results, such as peel strength, against each batch of bonded parts.
  • Trimming and post-cure tracking. Follow parts through deflashing and post-cure oven loads, with times and inspector release.

Operational bottlenecks to check

Compound batches and parts are separate worlds

The mixing room keeps batch sheets and the press operator keeps a shot count, so a rejected bag of bushes has no batch behind it.

Cure settings are chalked on the press

Time and temperature for each mould are written on a tag or in the operator’s head. A new operator runs a different cure and the parts come out under-cured or burnt.

Cavity faults hide in the mix

A damaged cavity makes bad parts in every shot, yet the output from all cavities goes into one bin, so rejects are counted and the cavity behind them is not. Cavities wear out quietly.

Preform weight drifts

Strips are cut by hand or on a cutter and weighed on a bench scale. Too light gives short fills. Too heavy gives flash, extra trimming and wasted compound.

First-off approvals are lost

The buyer’s signed sample and its measurements go into a drawer. A later run is judged against memory rather than the approved piece.

Follow the work across teams.

This is a planning flow. Confirm the steps, owners and approval rules against your actual operation.

  1. 1. Enquiry and drawing

    The drawing arrives with a compound grade and a Shore A hardness range. The estimator quotes from compound cost, preform weight, cure time and cavity count.

  2. 2. Mould and sample

    The mould is made or drawn from the tool store. A first-off sample is moulded, measured against the drawing with a dial caliper and durometer, and sent to the buyer for approval.

  3. 3. Compound mixing

    The mixing room makes a batch on the two-roll mill or internal mixer, tests it on a rheometer and durometer, and releases or holds the compound for the presses.

  4. 4. Moulding

    Preforms are cut to weight and loaded into the cavities. The press runs at the recorded cure, and shots and rejects are logged against each cavity.

  5. 5. Trim, post-cure and inspection

    Flash is removed by trimming or cryogenic deflashing. Post-cure ovens run where the compound needs them, and inspectors check dimensions and surface faults such as flow marks and backrinding.

  6. 6. Bag and deliver

    Parts are counted into labelled bags. A delivery note and any requested certificate go out with them, and the invoice follows the order.

Roles and responsibility boundaries.

For owners

See presses running, batches on hold, scrap by cause, mould life and balances by buyer, all on one screen.

For the mixing room

Record each batch recipe, its scorch and cure times and hardness result, then release or hold the compound for the presses.

For press operators

See the cure settings and preform weight for the mould fitted. Log shots and rejects per cavity as the press cycles.

For quality inspectors

Compare parts with the approved sample, record dimensions with the gauge, check flash and surface faults, and decide release.

For planners and dispatch

Book presses and group mould changes so one compound serves a whole day. Issue delivery notes for the bags counted.

Reports your managers need.

  • Orders by press with compound batch and cure
  • Batches released, held and rejected
  • Scrap by cause, mould and cavity
  • Shots since cleaning by mould
  • Compound used against parts moulded
  • Bonded part test results by batch
  • Buyer balances, oldest due first

Connections to scope

  • Rheometer result file import
  • Weighing scale input
  • Barcode and bag label printing
  • Email
  • WhatsApp or other messaging
  • Accounting software export

Confirm data access, record ownership and the exchange method for each connection. Inclusion here does not mean every connection is available in a standard package.

Setup decisions and adoption risks.

Use these requirements to plan phases, data migration and user training. Agree the release sequence after reviewing your current systems.

Compounds and tests

Your recipes and the tests you run, such as rheometer curve, durometer hardness and specific gravity, are set up with their limits for each compound grade.

Moulds and presses

Each mould, cavity count and press is entered, with the shot limits that call for cleaning. Tonnage and platen size are noted for the planner.

Cure rules

Cure time, temperature and pressure by mould and compound are loaded from your press tags, which can then come off the wall.

Open orders and stock

Your buyer list, live orders, compound on the shelf and approved samples are carried over at the outset.

Units and currency

Kilograms or pounds, Shore A or other hardness scales, millimetres or inches: each buyer sees its own. Currency and tax rules are set per country at rollout.

Limitations to settle before implementation

  • A shop that moulds a few samples a month on one press can work from a job book.
  • Cutters of gaskets from sheet will find Rubber Gasket Manufacturer Management Software closer, and makers of O-rings and seals may prefer Seal and O-ring Manufacturer Management Software.

Modules to consider first.

These functions connect to the operating model above. Confirm each one against the work your business actually runs.

Choose the operation you want to improve.

Use these activities to explain your scope. Your business does not need every function in the directory.

  • Every drawing answered with a question about the parting line or the tolerance
  • Tool cost and piece price explained in one clear sheet
  • Vendor registration with auto, appliance and pump makers
  • First article and sample approval chased with the customer's quality team
  • Rubber-to-metal bonding shown as a second family beside plain moulded parts
  • Customer-owned tools in your shop turned into a second part family
  • Overseas buyers who source rubber parts from India
  • Tool room and mould repair offered as its own service
Talk to us

Start with the problem your team can describe.

Bring a sample record and show where information is copied, missed or waiting for approval. Scope the first useful change from there.

What happens after you share your requirements

  1. We review your brief and the systems you already use.
  2. We clarify the workflow, missing information and the work to consider first.
  3. The proposed scope sets out the deliverables, responsibilities and dependencies.
  4. Review the scope and commercial terms before deciding whether to proceed.

Start with your requirements

Describe your current process, the people involved and the change you need. Start with the details you know; we can clarify the rest together.

Share your requirements